specifcations subject to change without notice. all dimensions in inches. ? copyright 2009 the connor-winfeld corporation 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com 3.3v surface mount crystal clock oscillator hsm6 xo the connor-winfeld hsm613, hsm623, and hsm633 are 7.5mm x 5mm, 3.3v hcmos, surface mount, fixed frequency crystal oscillators (xo) designed for use in all applications requiring precision clocks. the rohs compliant surface mount package is designed for high-density mounting and is optimum for mass production. operating specifcations parameter minimum nominal maximum units notes frequency range (fo) 1.544 - mhz hsm613 125 hsm623 170 hsm633 170 frequency tolerance - ppm 1 hsm613 -25 25 hsm623 -50 50 hsm633 -100 100 operating temp range -40 - 85 c supply voltage (vdd) 3.0 3.3 3.6 vdc supply current (icc) - - ma 1.544 to 31.999 mhz 15 32 to 49.999 mhz 20 50 to 66.999 mhz 25 67 to 124.999 mhz 40 125 to 170 mhz 50 absolute maximum ratings parameter minimum nominal maximum units notes storage temperature -55 - 125 c supply voltage (vcc) -0.5 - 5.0 vdc features: 1.544 to 170 mhz 3.3v operation rohs compliant tri-state enable/disable power saving function: 10ua when disabled overall frequency tolerance: hsm613 25 ppm hsm623 50 ppm hsm633 100 ppm temperature range: -40 to 85c ceramic surface mount package tape and reel packaging notes: 1. inclusive of calibration @ 25c , frequency stability vs temperature, supply voltage change, load change, shock and vibration, 10 years aging. 2. oscillator output is enabled with no connection on pad 1 bulletin sm044 page 1 of 2 revision 12 date 12 jan 2009 us headquarters: 630-851-4722 european headquarters: +353-61-472221 input characteristics parameter minimum nominal maximum units notes enable voltage - (vih) 70% vdd - - vdc 2 disable voltage - (vil) - - 30% vdd vdc enable time - - 10 ms disable time - - 150 ns output disable current (lcc) - - 10 ua hcmos output characteristics parameter minimum nominal maximum units notes load - - 15 pf voltage high (voh) 2.91 - - vdc low (vol) - - 0.33 current high (loh) -2 - - ma low (lol) - - 2 duty cycle at 50% of vcc 45 50 55 % rise / fall time: 20% to 80% 1.544 to 19.999 mhz - 3.0 6.0 ns 20.00 to 49.999 mhz - 2.0 4.0 50.00 to 99.9999 mhz - 1.5 3.0 100.00 to 170 mhz - 0.5 1.0 start-up time - - 10 ms jitter (10 hz to 20 mhz) - - 5 ps rms (12 khz to 20 mhz) - - 1
specifcations subject to change without notice. all dimensions in inches. ? copyright 1998 the connor-winfeld corporation 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com bulletin sm044 page 2 of 2 revision 12 date 12 jan 2009 pin connections 1: tri-state e/d 2: ground 3: output 4: vdd dimensional tolerance: .02? (.508mm) .005? (.127mm) dimensional tolerance: .02? (.508mm) .005? (.127mm) soldering general conditions 260c max x 10 sec max x 2 times max or 230c max x 180 sec max x 1 time typical operation data (vapor phase refow) 20 to 100 sec up to 215c, 50 sec at 215c, then down to room temperature per 1 to 5c / sec environmental characteristics temperature cycle the specimen shall meet electrical characteristics after tested 5 cycles of -55c / 30 minutes and +125c / 30 minutes hermetical no bubbles appear in flourinert (fc-43) at 125c 5c for 5 minutes solvent resistance marking will withstand immersion in isopropyl alcohol or trichloroethylene suggested pad layout ordering information mechanical characteristics free drop the specimen shall meet electrical characteristics after tested 3 times, free drop testing on the hard wooden board from a height of 75 cm. vibration the specimen shall meet electrical characteristics after tested by the following conditions: 10-55hz 1.5mm amplitude, 55-2000 hz 20 g's, 2 hours for each plane thermal shock after applied thermal shock of 260c max x 10 sec max x 2 times, or 230c max x 180 sec max, the specimen shall meet electrical characteristics solderability (eiaj-rcx-0102.101 condition 1a) 1) flux: mil-f-14256 (ww rosin=25%, isopropyl alcohol = 75%) 2) solder: qq-s-571 (sn = 63%, pb = 37%) 3) solder bath temperature: 235c 5c 4) depth of immersion: up to electrical terminal 5) immersing time: within 2 sec 0.5 sec into solder bath after performing the above procedures, a newly soldered coverage shall be greater than 90% test circuit output waveform tape and reel dimensions package characteristics package hermetically sealed ceramic package and metal cover hsm633 - 125.0m clock series center frequency t f t r "1" level 80% "0" level 50% 20% symmetry
|
